3 amber 1 white dell

November 26th,

July 12th, My inspiron laptop cannot be turn on. When I plug-in the power and hit the power button, battery light and power light on. Then battery light shows 3 yellow and 1 white. After this pattern goes on for around 7 times, battery light and power light turn off.

3 amber 1 white dell

August 30th, When I plug in the power adapter, I first get a white light and 3 blinks of amber after that from the light next to the plug. Is that very low battery or maybe a bad battery? The laptop comes on just for a few seconds but has a black screen and the caps lock light is lit. I'm sure the power adapter is good. I have this problem too 1. Responses 6. September 13th, Had 3 problems at once: bad cmos battery, bad main battery, and damaged power plug. The power jack has 3 pins encased in a phenolic ring.

Go to Solution. When you have the report compare the Design Capacity value versus the Full Charge Capacity value as shown by the report. July 12th,

November 9th, So this started about 2 weeks ago i had problems that the battery was plugged in but wasn't charging so i bought a new battery off amazon that is the right battery type. So when it came in i swapped the batteries and then powered on the laptop at first it worked and updated itself after 20 mins or so it turned off. After that it didn't power on, i could hear the fans running then hearing them turn off after a couple of seconds. So i removed the battery and held the power button for 30 seconds to try to reset the laptop but it still didnt turn on or power anything. I checked the adapter with the multimeter and it fine. Checked the cmos battery and its fine even replaced it.

This post is more than 5 years old. January 27th, I haven't been able to find the error codes anywhere. Inspiron 15 I have this problem too Responses 5. I just needed to go into the BIOS and select "restore defaults" and it was fixed. The desktop reference guide ended up solving it for me. Still not resolved?

3 amber 1 white dell

Dell Precision Workstation systems have a long history of built-in diagnostic indicators. These can be audible beeps, power buttons that display different states and colors, specific diagnostics LEDs or a combination of them all, in order to indicate at which point during the Power On Self-Test POST a system is having issues. The following article is a reference guide to the codes available on each model and what those codes mean. These change through the various models and years. These indicators are merely a starting point for narrowing down any troubleshooting to be carried out to identify the cause of your current issue. You can use this as a starting point to narrow down the proper troubleshooting guide required, or you can contact technical support for further help and they will be looking for these indicators as well. With the latest series, the Power Button state now gives a new blink and color shift pattern that uses both Amber and White power LED flashes to indicate where it had a problem. You can identify these systems by the fact that there is no Diagnostics LED block on the front of the unit. With this series, the diagnostics indicator LEDs have been removed.

Annie runes

Beep Codes Table. A possible system board, power supply, or device failure has occurred. If still under the purchased warranty, click the " Get Help Now " icon on the right to start a live chat session. Ensure that all hard drive and optical drive cables are properly connected to the system board. Products Solutions Services Support Community. System is on with no failures detected. Then expecting it to be a battery problem, i connected a new original Dell battery. Check the computer setup to ensure that the boot sequence is correct for the devices that are installed on your computer. Another failure has occurred. Another failure has occurred. This is the normal power state of a functioning machine. Power Rail Failure: EC ran into a power sequencing failure. I did not seem to be able to bypass the BIOS interruption. Probably should start a new thread but my issue is closely related: Installed a new battery two years ago and all worked fine.

Dell Latitude laptops have various integrated visible and audible diagnostic indicators to help identify possible failure of hardware components causing specific symptoms. Most of these symptoms are related to the laptop not being able to boot to Windows, displaying a black screen from startup, and so on.

Appropriate memory modules were detected but appear to be incompatible or in an invalid configuration. One blink followed by a short pause, one blink then a long pause, then it repeats. A possible expansion card failure has occurred. As you noted, some users have even reported that their system would not boot up after SupportAssist updated their BIOS and they had to downgrade their BIOS before they could boot up their system. View All. A faulty charge circuit on the system board, which will require a replacement mainboard. Memory configuration or incompatible error The memory subsystem configuration activity is in progress. If nothing works, replace the motherboard, memory, or processor. Beep Codes Table. Start a Conversation. I don't know what could possible be wrong if its the bios or a short in the motherboard. That error can relate to a bad reserve CMOS battery, but by itself, that won't prevent powerup so there has to be another issue with the system.