Astm b221 pdf

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes1 This standard is issued under the fixed astm b221 pdf B; the number immediately following the designation indicates the year of original adoption or, astm b221 pdf, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the U. Department of Defense.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes1 This standard is issued under the fixed designation B; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the U. Department of Defense. Referenced Documents aluminum alloys Note 1 and tempers shown in Table 2. This specification may not address the Alloy Rolled or Cold Finished Bar, Rod, and Wire manufacturing processes, integrity testing, and verification required for B Specification for Aluminum and Aluminum-Alloy fluid-carrying applications involving pressure. Magnesium Products 1.

Astm b221 pdf

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys. All the products should be produced by hot extrusion or similar methods. The chemical composition of each material is determined in accordance with the specified suitable chemical and spectrochemical test methods. Samples for chemical analysis should be taken when the ingots are poured or from the finished or semi-finished products by drilling, sawing, milling, turning, or clipping. Tensile properties, elongation, and yield strengths of each product should conform to the requirements listed herein. Elongation requirements are not applicable for materials with sizes smaller than the specified limits. Note 1: Throughout this specification, the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 3: Pipe and tube products listed in this specification are intended for general purpose applications. This specification may not address the manufacturing processes, integrity testing, and verification required for fluid-carrying applications involving pressure. See Specification B , as appropriate, for use in surface condensers, evaporators, and heat exchangers. A PDF redline is a quick and easy way to compare all of the changes between the current, active standard and the previous version.

Retest and Rejection

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys. All the products should be produced by hot extrusion or similar methods.

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys.

Astm b221 pdf

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys. All the products should be produced by hot extrusion or similar methods. The chemical composition of each material is determined in accordance with the specified suitable chemical and spectrochemical test methods. Samples for chemical analysis should be taken when the ingots are poured or from the finished or semi-finished products by drilling, sawing, milling, turning, or clipping.

Obituaries miramichi nb

Please be aware that carriers will not deliver packages to Post Office Boxes. XX or 1. Prohibited Uses. K Lead 0. Carousel Next. Delivery Formats and Service. International Standard Shipping International orders are delivered via courier post services which can be either a postal service, courier service, or a combination of both. See Specification B, as Wrought Products appropriate, for use in surface condensers, evaporators, and heat exchang- ers. Properties in Specification Table 2 are not based on the Zirconium and Titanium algorithm. See 8. Standard Service is untraceable. Source Inspection Committee B07 has identified the location of selected changes to this standard since the last issue B — 12a that may impact its use. NOTE 7—It is difficult to obtain a reliable analysis of each of the 5. M Tentative; properties subject to revision.

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered?

B Document 12 pages. Other methods may be used only when C The discontinuity class limits are defined in Section 11 of Practice B Create an Account. Carousel Next. JavaScript seems to be disabled in your browser. See 8. Martin 3rd Edition Document 20 pages. User Settings. H Minimum yield strength for tube, Not registered? Copyright Notice. Jump to Page.