Snake knot paracord

A single color knot, this technique creates a slim, snake knot paracord, tight pattern that is ideal for places where a thinner cord is desired such and zipper pulls or lanyards. The snake knot is also suitable for all thicknesses of cord and is a versatile, easy technique to master. Difficultly level: Easy Time required: 15 minutes. Things to do: Black parachute cord — or other colors of your snake knot paracord.

This instructable will show how to make a wrist lanyard using paracord and the snake knot. The lanyard can be used to secure a key chain, knife, multi-tool, flashlight, cell phone, camera, binoculars, compass, etc. More projects, links, knot references can be seen on my blog page, Stormdrane's Blog. You'll need about 4. The paracord I used is from the Supply Captain.

Snake knot paracord

.

Difficultly level: Easy Time required: 15 minutes. You'll need about 4. By Stormdrane Stormdrane's Blog Follow.

.

Use beginner friendly, basic knots and learn how to make a paracord snake with only 3 simple steps! Kids will have a blast bending and shaping their snake and making it slither around. This knotted craft is easy and fun, perfect for summer camp and Scouts! This post contains affiliate links. If you use these links to buy something we may earn a small commission which helps us run this website.

Snake knot paracord

Last Updated: March 29, References. This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. There are 25 references cited in this article, which can be found at the bottom of the page. This article has been viewed 82, times. Learn more

Twister on bed

You may also like May 15, Also used are scissors, tape measure or ruler, lighter, hemostats or needle nose pliers not necessary, but they make it much easier , and a swivel clip, key ring, snap hook, cell phone lariat, carabiner, or whatever attachment you prefer to use. More About Stormdrane ». Use the scissors to trim off the excess cord and quickly melt the ends with a lighter so they don't fray. I bring it under all the other cords, working the hemostats under the previously tightened knot and pulling the cord back thru. You may remove a small amount of the paracord's inner strands by pulling them out, trimming with scissors, and pulling the paracord outer sheath back over the strands, leaving room to insert the other color. More by the author:. Again flipping the work over, you'll see two parallel cords of the same color which will be split with the cord on the right going under, around, and pulled thru with the hemostats, then tightened up. If done in one color, it will be one continuous 4. You'll notice from the photos of both sides of the lanyard, that one side has the snake knots alternating all the way down and the other has a set of parallel knots at the top and botton of the sequence of knots. Pull the new right hand leg into another loop and pass it through the first loop. For this tutorial I'm measuring the wrist loop at about 10 inches from the attachment. Things to do: Black parachute cord — or other colors of your choice.

But instead of carrying around a small hank of paracord in your back pocket, you can wear it in the form of a stylish and handy bracelet. The following method is one of my favorites, combining the intriguing, easy and compact snake knot with a hardware-free adjustable closure as made Internet Famous by the most recent Mad Max movie. If significantly smaller, use less.

Pull to tighten and repeat until you have reached the desired length. If done in one color, it will be one continuous 4. Difficultly level: Easy Time required: 15 minutes Things to do: Black parachute cord — or other colors of your choice Things to do: 1. May 15, I bring it under all the other cords, working the hemostats under the previously tightened knot and pulling the cord back thru. The snake knot is also suitable for all thicknesses of cord and is a versatile, easy technique to master. More projects, links, knot references can be seen on my blog page, Stormdrane's Blog. I've added a series of photos showing the steps I use. Then tightening up the knot keeping the cord from twisting and working it up against the previous knot. For this tutorial I'm measuring the wrist loop at about 10 inches from the attachment.